Sharp AH-PN13 Manuale di Installazione

OPERATION MANUAL INDOOR UNIT OUTDOOR UNITAH-PN10 AU-PN10AH-PN10-GY AU-PN10AH-PN13 AU-PN13AH-PN13-GY AU-PN13AH-PN19 AU-PN19AH-PN24 AU-PN24AH-L10 A

E-8The vertical airflow louvre is set obliquely upward to deliver cool air to the ceiling in order to avoid direct airflow.1 During operation, press t

ENG-E-9TIMER ON1 Press the TIMER ON button and set the time as desired.• The orange TIMER lamp ( ) will light up.• The time setting will count down

E-10CANCEL11When the ONE-HOUR OFF TIMER is set, the unit will automatically turn off after one hour.1 Press the ONE-HOUR OFF TIMER button.• The remot

ENG-E-119,000/12,000 BTU18,000/24,000 BTUBe sure to disconnect the power cord from the wall outlet or turn off the circuit breaker before performing a

E-12Check the following points before calling for service.The unit does not operate• Check if the circuit breaker has tripped or the fuse has blown.T

ENG-E-13INSTALLATION MANUALSAFETY PRECAUTIONSSPLIT TYPE ROOM AIR CONDITIONERACCESSORIESITEMS Q’ty ITEMS Q’ty ITEMS Q’ty1 MOUNTING PLATE13 DRY BATTERY2

E-14NOTES ON LOCATIONS INDOOR UNIT1. Keep the air outlet clear of any obstacle so that outgoing air flows smoothly in the entire room.2. Make a drain

ENG-E-15INSTALLATION DIMENSION OF INDOOR UNIT860108A125J175115IFEDJEAFID2924530Length unit: mmCenter of wall holeCenter of wall holeOutline of indoor

E-16Installing the mounting plate(1) Referring to the “INSTALLATION DIMEN-SION OF INDOOR UNIT”, mark the location for the fixing holes and the piping

ENG-E-1712345(1) Remove the screw and pull out the drain hose.(2) Pull out the drain cap.(3) Reconnect the drain hose to the right and insert the dr

OM_AH-PN10 13GY_EN.indd 2OM_AH-PN10 13GY_EN.indd 2 12/22/11 6:30:09 PM12/22/11 6:30:09 PM

E-18SHORT SCREW 5 CABLE COVERCAUTIONS: • Be very careful not to confuse the terminal connections. Wrong cabling may damage the internal control cir

ENG-E-19OUTDOOR UNIT INSTALLATION ABReferring to the figure, firmly fasten the outdoor unit with bolts.ระยะหางของขาตั้งตัวเคร องปรับอากาศระยะหางของ

E-20CONNECTING THE PIPES TO THE OUTDOOR UNITPiping can be made in four directions, choose whichever direction convenient according to unit’s installat

ENG-E-21AIR REMOVALLo HiValve shaft cap tightening torquePipe size Torqueรุนเคร องปรับอากาศรุนเคร องปรับอากาศLiquid side 1/4" 24±3N · m (2.4±

E-22CONNECTING THE CABLE TO THE OUTDOOR UNIT9K 12K-Btu/h type(1) Process the end of the connecting cable for the outdoor unit.(2) Remove the control b

ENG-E-23POWER CABLINGPower supply cableBlueBrownGreen/Yellow-stripedPower supplyBlueLiveGreen/Yellow-stripedPrepare a dedicated power supply circuit.

E-24DETACHING THE UNIT FROM THE MOUNTING PLATE“ ” mark. Push the “” marks at the bottom of the indoor unit and pull the bottom of the unit. When the

OM_AH-PN10 13GY_EN.indd Sec1:25OM_AH-PN10 13GY_EN.indd Sec1:25 12/22/11 6:30:42 PM12/22/11 6:30:42 PM

Printed in ThailandTINSEA720JBRZ 11M- TH 2OM_AH-PN10 13GY_EN.indd Sec1:26OM_AH-PN10 13GY_EN.indd Sec1:26 12/22/11 6:30:42 PM12/22/11 6

ENG-E-1ENGLISHPlease read this manual carefully before using the product. This manual should be kept in a safe place for handy reference.IMPORTANT SAF

E-2 1 Inlet (Air) 2 Open Panel 3 Air Filter 4 AUX Button 5 Receiver Window 6 Vertical Airflow Louvre 7 Horizontal Airflow Louvre 8 Outlet (Air) 9 OPE

ENG-E-3 1 Inlet (Air) 2 Open Panel 3 Air Filter 4 AUX Button 5 Receiver Window 6 Power Supply Cord 7 Vertical Airflow Louvre 8 Horizontal Airflow L

E-4REMOTE CONTROL 1 TRANSMITTER 2 DISPLAY 3 ON/OFF Button 4 THERMOSTAT Button 5 DISPLAY Button 6 ONE-HOUR OFF TIMER Button 7 PLASMACLUSTER Button 8

ENG-E-5AUX7 m18,000/24,000 BTUAUXLOADING BATTERIES1 Remove the battery cover. 2 Insert two batteries. (AAA(R03))Make sure the (+) and (-) polarities

E-623141 Press the MODE button to select the operation mode. 2 Press the ON/OFF button to start operation.• The red OPERATION lamp ( ) will light

ENG-E-7The air conditioner works at the maximum power and optimum louvre direction to makes the room cool rapidly.1 During operation, press the POWER