Sharp PG-M20XL Manuale Utente

BA72ALCD TFT 12.1" Flat ScreenUser Manual

Unpacking and checking the Delivery UnitUnpack the parts and check to see whether the delivery matches the infor-mation on the delivery note. The deli

BA72A ComponentsScreen ModuleThe screen module represents the main unit of the BA72A. It comprises ofa TFT-LCD colour screen, the TFT-interface and an

“Stretching” is only possible when a separate TFT conroller is used. So,when operating with the BA72A and the integrated TFT controller at theMedia GX

TFT-Controller-ATFT-Controller-AThe TFT-controller-A is a plug-in-controller with a PCI-interface. There aretwo connections fora 40-pin MDR connector

Panel of TFT- controller-ABoard layout (TFT-controller-A)11240569COM6DSUB socketBA72A connectorincl. COM5, LCD interfaceand loudspeakerMDR connectorSp

Capacative Touch Screen (Option)GeneralThe TFT Touch Screen works according to the principle of a change inanalog capacitance. It has a glass screen w

The programming interface of the screen is identical to the mouse inter-face. Touch ScreenTouch Screen and Sleep ModeUsing the Touch Screen with a BEE

Touching the touch glass has the same effect as clicking the left mousebutton. You only need to apply a little pressure with the fingertip. In this ca

COM Board for Touch ScreenCOM BoardThe COM Board is an additional board for the TFT-controller-A with anISA bus interface that has 2 or 4 COM interfac

COM Interface InterruptsCOM5 COM6 COM7 COM7-8 COM6-8 InterruptIRQ9I9---I11IR9IRQ10I10 - - - I12 IR10IRQ11I5 - I4 I8 I13 IR11IRQ12I1---I6IR12IRQ15I3 I2

Published byWincor Nixdorf International GmbHD-33094 PaderbornBestell-Nr./Order No.: 01750022256BPrinted in Singapore

Assignment of COM port addresses and interrupts (installation details)Ensure that there is no conflict of hardware port addresses or interrupt re-ques

IRQ12, most likely conflict Mouse Port or PS/2 MouseThese types of mice are supported by Windows NT through theI8042PRT.SYS driver. The mouse usually

The AT COM Board manual numbers the COM ports from 5 to 8. The ori-gin of this numbering is from the BEETLE, which has COM1 to COM4 onthe motherboard.

be impossible for hardware reasons! The problem is, that in such a caseon the AT bus two different hardware instances would be fighting for thesame IR

Using shared interrupts for COM ports under Windows 95Under Windows 95, sharing COM ports doesn’t require special provisionsother than correctly speci

Board layout COM boardCOM7COM 5 /COM 6COM81122Interrupt JumperInterrupt RequestI8 I1I9I16IR15IR12IR11IR10IR 9IO 3IO JumperIO 1COM BoardGB - 18

LCD-TFT Adapter A-MediaGXmLCD-TFT Adapter A-MediaGXmIn the case of the BEETLE with GXmCPU the TFT adapter can be connec-ted with GXm CPU without TFT c

LCD-TFT Adapter A-CeleronLCD-TFT Adapter A-CeleronIn the case of the BEETLE with Ce-leron CPU the TFT adapter can beconnected with the Celeron CPU wi-

Resistive Touch Screen (Option)GeneralThe resistive TFT Touch Screen is constructed of a hard-coated polyestertopsheet that is overlaid on a conductiv

Construction of the resistive Touch Screen:How to OperateTouching the touch screen has the same effect as clicking the left mousebutton. You only need

BA72ALCD TFT 12.1" Flat ScreenUser ManualEdition July 2002

Installing and Securing the Screen into PlaceThe screens can be installed either with or without attached operatingelements, as a table top terminal o

Tubular Stand VersionNow fasten the screwon the footed standinto place again usingthe crosstip screw-driver.Ensure that the screwis in the correctposi

Adjustable Screen AngleAdjustable Screen AngleThe BA72A is fitted with a joint on the rear. You can optimize the angle ofthe screen depending on the v

Ergonomic Terminal WorkplaceErgonomic Terminal WorkplacePlease observe the following when setting up your terminal workplace:Avoid direct glaringand r

InstallationInstalling the Controller in the BEETLEFirst ensure that the controller is switched off and the mains supplyplug has been pulled out.Remov

In order to be able to install the TFT controller, you must first remove themetal panel that covers the free slots by loosening the screw.Set the jump

Connecting the Speaker CableConnecting the Speaker CableRemove the speaker cable from the BEETLE-CPU by simply unpluggingthe connector. The BEETLE /L

Connecting the BA72A to the BEETLE /20The hardware installation is carried out according to the installation of theBA72A to the BEETLE /L. When instal

Connecting the BA72A to the PCConnecting the BA72A to the PCFirst ensure that the controller is switched off and the mains supplyplug has been pulled

The touch function with a LCD TFT adapter-A has to be activated viaa jumper (see also jumper settings).The COM2 interface has to be covered and may no

Copyright © Wincor Nixdorf International GmbH, 2002The reproduction, transmission or use of this document or its contents is not permitted withoutexpr

COM2 with GXm BoardCOM2 for peripheralsCOM2 for touch function using the TFT adapterIf the BEETLE is delivered with TFT adapter with touch function, t

The Jumper layout of the Celeron Board+-AD1816AJSPS2/MouseMICKYB/ECOM4*COM3*USBCOM2*/ICOM2*COM1OUTCD-AUDIOAUDIO69000VGA/TFTPCI/ISALPTPCI-ONBOARDVGA/CR

COM2 with Celeron BoardCOM2 for peripheralsCOM2 for touch function ussing a TFT adapterIf the BEETLE is delivered with TFT adapter with touch function

Connecting the cableThe data cable is to be connected with the 40-pin connector of the TFTadapter. Take care that the thickening of the cable (Ferrit)

Now plug in the cableuntil it snaps in (see il-lustration).When removing thecable press on theconnector release.Installing a LCD-TFT Adapter ANever op

Inserting the CableInserting the CableThe cable cover is lo-catedinthebaseplate.Lift the cable cover .Pull the cable coverforward in the directionof t

Releasing the Cable ConnectionReleasing the Cable ConnectionNever remove a cable from a connector socket by simply pulling on thecable. Always remove

Software InstallationThe software installation refers to the installation of corresponding displaydrivers; the installation of the touch screen compri

Software InterfacesTouch ScreenTouch ScreenTouching the screen corresponds to press the left mouse key. The touchscreen programming interface is ident

Automated Logic Diagram (ALD) and PinAssignments7413140pin. MDRKYBDBEETLE-CPUCASHDRCOM4COM3COM2COM1COM640pin MDRFREE ISA-SlotCOM7*COM8*LAN Piggy Back

ContentsIntroduction ... 1From Point-of-Sale to Point-of-S

InterfaceAutomated Logic DiagramThe LCD interface is connected to the TFT controller via a 40-pin cable.The inverter, LCD display, touch screen contro

Pin AssignmentsPin Assignments ControllerBA72A Connectors of the 40-pin TFT InterfacePIN # Signal PIN # Signal1 HUOUT 2 RXCN3 GND 4 RXCP5 P5VLCD 6 P5V

COM 6 Interface of the ControllerPIN # signal1 P12VF2RxD23TxD24DTR25 GNDF16DSR27RTS28CTS29P5VFInternal Speaker Connector for Controller and BEETLE-CPU

Internal Connecting SocketPIN# COM7 COM81P5VF P5VF2 GNDF GNDF3 DCD3 DCD44 GND GND5 CTS3 CTS46 DTR3 DTR47 RTS3 RTS48 TxD3 TxD49 DSR3 DSR410 RxD3 RxD411

External Connecting SocketPIN# with power supply w/o power supply1 +12V DCD2RxD RxD3TxD TxD4DTR DTR5 GND GND6DSR DSR7RTS RTS8CTS CTS9+5V RIPin Assignm

Technical DataThe following operating conditions are valid for a BA72A TFT that is fittedwith all the available modules (LCD flat screen, touch screen

TFT/ LCD ScreenLCD ScreenTechnical DataFrequenciesHorizontal (KHz) 29Vertical (Hz) 47SolutionsHorizontal 800 pixel (SVGA)Vertical 600 lines (SVGA)Colo

BA72ADimensionsScreen size 12.1" (30,7 cm)Active screen size(horizontal x vertical)246 mm x 185 mmCable length 3 m / 5mDimension Display Housingw

Current ConsumptionCurrent ConsumptionTFT Controller370 mA + 5V50 mA +12V50 mA -12VScreen ModuleConsisting of an LCD display, touch screen incl. contr

LCD-Controller-A TFT/PCITFT-ControllerInterfacePCI, 32 BitModeSVGAResolution800 x 600 x 256 colours (SVGA), 64kImage repeat memory2MBScreen memoryText

Resistive Touch Screen (Option)...21General...

COM BoardCOM-Board ControllerSystem interfaceISA, 8 MHzI/O-addresses forCOM interfaces3 address records 2E0, 330, 320 thatcan be set by jumperInterrup

Manufacturer’s Declaration and ApprovalGeneral AuthorizationThis device fulfills the requirements of the EEC standard89/336/EWG “Electromagnetic Compa

Tested SafetyThe BA72A has been awarded theGS symbol for “Geprüfte Sicherheit”(tested safety). BA72/A fulfills the re-quirements for ergonomy accordin

Safety InstructionsThis device conforms to the corresponding safety regulations for informati-on technology devices, including electronic office machi

Instructions for MaintenanceManufacturer’s Certificate and Notes Instructions for MaintenanceClean your BA72A regularly with an appropriate surface cl

The BA72A is manufactured without the use of CFCs und CCHS and isproduced mainly from reusable components and materials. The processedplastics can, fo

AppendixAbbreviation IndexASCII American Standard Code for Information InterchangeAT Advanced TechnologyBIOS Basic Input Output SystemCFL Cold cathode

COM7 and COM8 Interfaces of the Controllers for BEETLE /XL ... 45Internal Connecting Socket ...

IntroductionFrom Point-of-Sale to Point-of-Service“The customer is king”, a motto that seems so simple and yet it demandsa permanently increasing supp

The low-energy, flickerfree and radiation-free colour monitor of the BA72Ais an Active-Matrix-Display in TFT-technology (Thin Film Transistor).Therefo