Sharp AR-168N Specifiche Pagina 24
- Pagina / 177
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
AR-168N/168L UNPACKING AND INSTALLATION 5 - 7
11) You will return to the window of step 8). If you wish to install But-
ton Manager or Sharpdesk, click the "Utility Software" button.
If you do not wish to install the Utility Software, click the "Close"
button and go to step 14).
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the "Yes" button to
restart your computer.
Installing the Utility Software
12) Click the "Button Manager" button.
To view detailed information on the software, click the "Display
Readme" button.
Follow the on-screen instructions.
If you wish to install Sharpdesk, click the "Sharpdesk" button in
this window and follow the on-screen instructions.
Caution:
• Button Manager can only be used when the machine is connected
by a USB cable.
• The scanner function of Sharpdesk can only be used when the
machine is connected by a USB cable.
Caution: If the following screen appears during installation of Sharp-
desk, click the "Skip" button or the "Continue" button as
appropriate to continue the Sharpdesk installation.
If "Skip" is selected, the Sharpdesk installation will continue
without installing Sharpdesk imaging.
If "Continue" is selected, Sharpdesk Imaging will be installed.
If Imaging for Windows is installed on your computer, Sharp-
desk Imaging will overwrite Imaging for Windows.
13) When installation of Button Manager is finished, you will return to
the window of step 12). Click the "Close" button.
A message will appear instructing you to connect the machine to
your computer. Click the "OK" button.
Note: After the installation, a message prompting you to restart your
computer may appear. In this case, click the "Yes" button to
restart your computer.
14) Make sure that the power of the machine is turned on, and then
connect the USB/parallel cable.
Windows will detect the machine and a Plug and Play screen will
appear.
Caution: If the following message appears on your computer screen,
close it.
A window regarding "HI-SPEED USB Device" will then
appear. Close the window.
This message appears when the machine's USB 2.0 mode is
not set to "HI-SPEED". For information on switching the USB
2.0 mode.
15) Follow the instructions in the plug and play window to install the
MFP driver.
Follow the on-screen instructions.
Caution: If you are running Windows XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway".
Note: A "USB 2.0 Composite Device" installation window may appear
prior to this procedure. In this case, follow the instructions in the
window to install the USB 2.0 Composite Device.
This completes the installation of the MFP driver.
• If you installed Button Manager, set up Button Manager as explained
in "C. Setting up button manager".
(2) Windows 98/Me/2000 (USB)
1) The USB cable must not be connected to the machine. Make sure
that the cable is not connected before proceeding.
If the cable is connected, a Plug and Play window will appear. If this
happens, click the "Cancel" button to close the window and discon-
nect the cable.
Note: The cable will be connected in step 8).
2) Perform steps 2) through 7) in "Custom installation".
3) Click the "MFP Driver" button.
To view detailed information on the software, click the "Display
Readme" button.
4) The "Welcome" window will appear. Click the "Next" button.
05_UNPAC.fm 7 ページ ２００５年１１月１８日 金曜日 午後５時２９分
- DIGITAL MULTIFUNCTIONAL 1
- CAUTION 2
- CONTENTS 4
- [1] GENERAL 6
- [2] SPECIFICATIONS 7
- 3. Copy performance 8
- 4. SPLC printer 9
- 5. Scan function 9
- [3] CONSUMABLE PARTS 10
- 4. TD cartridge replacement 11
- 1. Appearance 12
- 2. Internal 12
- 18 19 20 21 13
- 4. Motors and solenoids 14
- 5. Sensors and switches 15
- 6. PWB unit 16
- 7. Cross sectional view 17
- 1. Copier installation 18
- 2. Cautions on handling 18
- Lock Unlock 19
- Grasp here and turn in 19
- CAUTION tape 19
- Protective pins 19
- Pressure plate lock 21
- [Custom installation] 23
- (1) Windows XP (USB/Parallel) 23
- (2) Windows 98/Me/2000 (USB) 24
- C. Setting up button manager 27
- (1) Windows XP 27
- (2) Windows 98/Me/2000 27
- (1) Connecting a USB cable 28
- 11. Interface 29
- 12. Moving 29
- [6] COPY PROCESS 30
- 2. Outline of print process 31
- 3. Actual print process 31
- About DC 5.2kV 32
- Process controlling 33
- [7] OPERATIONAL DESCRIPTIONS 34
- 34 6 285 35
- 3. Laser unit 36
- 4. Fuser section 36
- (1) Heat roller 37
- (2) Separator pawl 37
- (3) Thermal control 37
- (4) Fusing resistor 37
- A. Initial state 41
- B. Front copy 41
- C. Back copy 41
- 8. Shifter 42
- [8] DISASSEMBLY AND ASSEMBLY 43
- Example of NG 44
- Charger wire 46
- Protrusion 46
- 3. Optical section 47
- CCD core 48
- 4. Fusing section 49
- Heat roller disassembly 50
- Heater lamp 50
- C. Assembly procedure 56
- Back Wire treatment 57
- 7. Rear frame section 59
- 8. Power section 60
- 9. Duplex motor section 60
- (1) Remove the rear cabinet 61
- (2) Remove the RSPF 61
- F. Sensor PWB 62
- G. Pickup solenoid 62
- H. Clutch 62
- (1) Remove the clutch unit 62
- (2) Remove the clutch 63
- (1) Remove the pickup unit 63
- (1) Remove the parts 65
- (2) Remove the parts 66
- T. Solenoid 67
- (1) Remove the reverse gate 67
- (2) Remove the solenoid 67
- [9] ADJUSTMENTS 68
- B. Image position adjustment 69
- (1) Lead edge adjustment 69
- B4 or 8 1/2″ × 14″ paper 70
- A4 size rear edge 70
- Scale image 70
- Paper rear edge 70
- White paper 71
- Test chart 71
- 3. High voltage adjustment 72
- 4. Duplex adjustment 72
- Document guide 73
- The trailing edge has a scale 73
- Table glass 73
- Scale (D-D mode) 73
- 6cm or more is required 74
- 2. Key rule 76
- 3. List of test commands 76
- Image loss, R = 4mm 101
- Chart back surface 105
- 5. Trouble codes 114
- [11] MAINTENANCE 117
- [12] USER PROGRAM 118
- B. Print mode 119
- [13] ELECTRICAL SECTION 121
- 2. Circuit descriptions 122
- (4) Reset circuit 127
- ASIC/CPU 128
- Tonner Motor Driver 129
- TD62064AF 130
- (10) OPE PWB 131
- (11) Carriage Unit 131
- (1) Noise filter circuit 131
- Voltage waveform 132
- [14]CIRCUIT DIAGRAM 134
- Serial EE-PROM 135
- MCU PWB (ASIC section) 136
- MCU PWB (Memory section) 138
- MCU PWB (Driver section 1) 140
- MCU PWB (Driver section 2) 142
- MCU PWB (Driver section 3) 144
- MCU PWB (IMC2 section 1/2) 148
- MCU PWB (Connector section 1) 152
- To Operational PWB 153
- To Mirror motor 153
- MCU PWB (Connector section 3) 154
- To 2nd. cassette 155
- MCU PWB (Modem I/F Connector) 157
- MCU PWB (Scanner I/F section) 158
- 2. OPERATION PWB 159
- To MCU PWB 161
- To Drum Initial Detector 161
- To FAX Key PWB 161
- POWER SUPPLY (120V/127V) 162
- (1) MCU SECTION (1/3) 164
- [15] FIRMWARE DOWNLOAD 167
- PROCEDURES 167
- 5. Installing procedures 171
- LEAD-FREE SOLDER 175
- CAUTION FOR BATTERY DISPOSAL 176
- COPYRIGHT 177
- 2005 BY SHARP CORPORATION 177
Prodotti e manuali riguardandi Apparecchi multifunzione Sharp AR-168N
Apparecchi multifunzione Sharp AR-156 Specifiche
(52 pagine)
(52 pagine)
(12 pagine)
Apparecchi multifunzione Sharp AR-151 Specifiche
(52 pagine)
(52 pagine)
Apparecchi multifunzione Sharp AR-810 Manuale Utente
(101 pagine)
(101 pagine)
(2 pagine)Newstar FPMA-D700D manuály
Uživatelské manuály a uživatelské příručky pro Držáky pro ploché obrazovky Newstar FPMA-D700D.
Poskytujeme 1 manuály pdf Newstar FPMA-D700D ke stažení zdarma podle typů dokumentů: Manuál s instrukcemi
Newstar FPMA-D700D Manuál s instrukcemi (2 strany)
Značka: Newstar | Kategorie: Flat panel desk mounts | Velikost: 0.28 MB |
Tabulka s obsahem
Další produkty a příručky pro Držáky pro ploché obrazovky Newstar
| Modely | Typ Dokumentu |
|---|---|
| FPMA-D940 |
Manuál s instrukcemi
Newstar FPMA-D940 flat panel desk mount,
2 stránky
|
| FPMA-D970 |
Manuál s instrukcemi
Newstar FPMA-D970 flat panel desk mount,
2 stránky
|
| FPMA-D950 |
Uživatelský manuál
Newstar FPMA-D950 flat panel desk mount,
4 stránky
|
| FPMA-D1130 |
Manuál s instrukcemi
Newstar LCD/TFT desk mount,
2 stránky
|
| FPMA-D1120 |
Manuál s instrukcemi
Newstar LCD/TFT desk mount,
2 stránky
|
| FPMA-DTB100 |
Manuál s instrukcemi
Newstar LCD/TFT toolbar,
2 stránky
|
| FPMA-D940DD |
Manuál s instrukcemi
Newstar FPMA-D940DD flat panel desk mount,
2 stránky
|
| FPMA-D700D3 |
Manuál s instrukcemi
Newstar FPMA-D700D3 flat panel desk mount,
2 stránky
|
| FPMA-D960 |
Manuál s instrukcemi
Newstar FPMA-D960 flat panel desk mount,
2 stránky
|
| FPMA-D700DD4 |
Manuál s instrukcemi
Newstar FPMA-D700DD4 flat panel desk mount,
2 stránky
|
| FPMA-D960D |
Manuál s instrukcemi
Newstar LCD/TFT desk mount,
2 stránky
|
| FPMA-D050DBLACK |
Manuál s instrukcemi
Newstar FPMA-D050DBLACK flat panel desk mount,
2 stránky
|
| FPMA-D1030D-4 |
Uživatelský manuál
Newstar LCD/TFT desk mount,
2 stránky
|
| FPMA-D1330SILVER |
Uživatelský manuál
Newstar FPMA-D1330SILVER flat panel desk mount,
4 stránky
|
| FPMA-D200 |
Manuál s instrukcemi
Newstar FPMA-D200BLACK flat panel desk mount,
2 stránky
|
| FPMA-D935 |
Manuál s instrukcemi
Newstar LCD/TFT desk mount,
2 stránky
|
| FPMA-D800 |
Uživatelský manuál
Newstar FPMA-D800 flat panel desk mount,
2 stránky
|
| FPMA-D935D |
Manuál s instrukcemi
Newstar FPMA-D935D flat panel desk mount,
2 stránky
|
| FPMA-D700D4 |
Manuál s instrukcemi
Newstar FPMA-D700D4 flat panel desk mount,
2 stránky
|
| FPMA-D910D |
Manuál s instrukcemi
Newstar FPMA-D910 flat panel desk mount,
2 stránky
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale